Evinrude/Johnson/OMC 250 HP 1997 Model 250TXEU, 250CXEU

Clymer - Evinrude/Johnson 85-300 HP Two-Stroke 1995-2002  B737

• Covers 85-300 HP, 2-Stroke
• 1995-2002
• Shop Manual

SELOC - Johnson/Evinrude Outboards, All V Engines, 1992-01 1st Edition  #1311

• Covers all 65-300 Hp, V4, V6 and V8 engines
• 1992-2001
• Repair Manual

18-2216 Sliding Clutch

• Sierra Sliding Clutch
• Meets or exceeds the original equipment quality
• Sierra part number: 18-2216
• Interchangeable with the following: GLM 22625, Evinrude/Johnson 337772, 37774, 334516, 336562, 910995, Mallory 9-72534, OMC 910995, 334516

18-2279 Lower Drive Shaft

18-3708 Prop Nut & Keeper

18-4223 Marine Thrust Washer

18-4231 Marine Prop Spacer

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Fits the following Evinrude Johnson Outboards (15 Spline)

• 90 HP V-4   1995-Newer
• 100 HP V-4 Commercial  1884-Newer
• 115 HP V-4  1995-Newer
• 130 HP V-4  1995 Newer
• 120 - 140 HP V-4  1985
• 140 HP V4  1989-1994
• 150 HP V-6  1978-Newer
• 150 HP V-6 Commercial  1993-Newer
• 155 HP V-6 Commercial  1978-Newer
• 175 HP V-6  1977-Newer
• 185 HP V-6  1984-1985
• 200 HP V-6  1976-Newer
• 225 HP V-6  1986-Newer
• 235 HP V-6  1978-1985
• 250 HP V-6  2001-Newer
• 2.6 Liter V6  1984-1985
• 250 HP V-8  1991-Newer
• 275 HP V-8  1986-1988
• 300 HP V-8  1986-1995
• 3.6 Liter V-8  1986-1987

Pitch is how far, in inches,  the boat would travel with one prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Other compatible propeller options: 

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Return to Propellers:

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust), Right and Left Hand Rotation

Fits the following Evinrude Johnson Outboards (15 Spline)

• 90 HP V-4   1995-Newer
• 100 HP V-4 Commercial  1884-Newer
• 115 HP V-4  1995-Newer
• 130 HP V-4  1995 Newer
• 120 - 140 HP V-4  1985
• 140 HP V4  1989-1994
• 150 HP V-6  1978-Newer
• 150 HP V-6 Commercial  1993-Newer
• 155 HP V-6 Commercial  1978-Newer
• 175 HP V-6  1977-Newer
• 185 HP V-6  1984-1985
• 200 HP V-6  1976-Newer
• 225 HP V-6  1986-Newer
• 235 HP V-6  1978-1985
• 250 HP V-6  2001-Newer
• 2.6 Liter V6  1984-1985
• 250 HP V-8  1991-Newer
• 275 HP V-8  1986-1988
• 300 HP V-8  1986-1995
• 3.6 Liter V-8  1986-1987

Pitch is how far, in inches,  the boat would travel with one prop rotation (under ideal conditions).  Higher pitch = Faster, Lower Pitch = Slower and more power.

OMC and Michigan Stainless Steel

Michigan Rapture Performance Stainless Steel

Michigan Ballistic High-Performance Stainless Steel

Other compatible prop options: 

90 - 300 HP Aluminum Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

90 - 300 HP Stainless Steel Propellers for V-6 Gearcase (15 Spline and Thru-Hub Exhaust)

Return to Propellers:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Stainless Steel V6 135-300 HP & 90-130 HP, 25" Shaft, 2-Stroke

• 15 Spline
• TBX Propeller Hub Kit 177283 for Evinrude/Johnson V6 Outboards  Amazon  eBay
•  
• Note:  There is also a TBX Hub Kit that makes these propellers work with  Suzuki / Mercury / Honda / Yamaha  V6 outboards. 177288    Amazon   eBay
•  
• 90 & 115 HP Evinrude® E-TEC®, 25" Shaft, 2004-thru
• 100 HP, 2004-thru
• 100 HP Commercial, 1984-thru
• 120 & 140 HP, 1985
• 130 HP, 1995-1996
• 130 HP Evinrude® E-TEC®, 2009-2010
• 135 HP, 2000-thru
• 140 HP (25"), 1989-thru
• 150 & 155 HP Commercial, 1978-thru
• 150-300 HP, Evinrude® E-TEC®, 2004-thru
• 175 HP, 1977-thru
• 185 HP, 1984-1985
• 200 HP, 1976-thru
• 225 HP, 1986-thru
• 235 HP, 1978-1985
• 2.6 liter, 1984-1985
• 250 HP, 1991-thru
• 275 HP, 1986-1988
• 300 HP, 1988-thru
• 3.6 liter, 1986-1987
• Evinrude® E-TEC® G2, 2015-thru
• Note: All V6 stainless steel propellers, fitted to Evinrude® E-TEC® G2 outboards require an additional purchase of custom fit G2 TBX™ hub kit #767683   Amazon   eBay

Stainless Steel, Stern Drive 15 Spline Propellers

15 Spline
800 Series

• 3.8 - 5.7 Liter, 1978-thru

OMC Cobra®

• 4.3 - 5.7 Liter, 1986-thru

OMC Sea Drive®

• 2.0 - 4.0 Liter, 1982-thru

OMC King Cobra®

• 7.4 - 8.2 Liter, 1990-thru

BRP Evinrude Polished Stainless Steel TBX Propellers

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation

BRP Evinrude Viper TBX Stainless Steel Propellers for Runabouts and General Recreation

If you want speed, you want the Viper prop.  It's longer swept blades and larger diameter give this prop a better grip on the water faster acceleration, and greater top-end speed.  Excellent on any recreational boat, from runabouts and cruisers to deck boats.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Versatile 3-Blade performance
• Excellent balance of speed and durability

BRP Evinrude Cyclone TBX Stainless Steel 4-Blade for Offshore Cruising and Runabouts

When you need a prop that can hold course straight and true in all water conditions, trust the Cyclone prop to maintain compass headings and stay hooked up in big water.  Designed for heavier and twin-engine boats as well as runabouts.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• Ultimate performance 4-blade offshore and runabout propeller
• Stays on plane with minimum RPM
• Tracks true in all water conditions
• Less vibrations and improved fuel economy

BRP Evinrude Rebel TBX Stainless Steel 3-Blade Props for Offshore Cruising

The Rebel propeller is designed and engineered to deliver improved midrange cruising and top-end performance on V6 Evinrude E-TEC.  Large diameter and efficient blade contour provide faster speeds at lower RPMs to deliver significant improvement in fuel economy.  You will get more miles to the gallon and a longer cruising range.  Standard rotation and counter-rotation models are available from 15 to 25-inch pitch.  Use the Rebel propeller on offshore boats, large runabouts, and even large pontoon boats to make them perform to their maximum potential.

• Uses TBX Interchangeable Hub
• Available in Standard RH Rotation
• Available in Counter LH Rotation
• High polish stainless steel
• Designed and engineered for efficient midrange cruising
• Improved fuel economy with a longer cruising range
• Use on offshore boats, large runabouts, and pontoon boats.

BRP Evinrude Raker H.O. Propellers for Bass Boats and High Performance

Looking to plane fast - and run faster?  The Raker II prop is specially designed for building up the engine RPMs and getting you on plane faster.  A great prop in surfacing conditions, especially when the boat is running over 50 mph.  Perfect for bass boats and high-performance boats.  The Raker propeller utilizes vent holes in the outer exhaust hub to allow exhaust gases to ventilate the blade area.  This allows the engine to build up RPMs and get the boat on plane faster.  At higher speeds, the water from rushing past the hub blocks these vent holes, preventing. them from ventilating the blades.  V6 Raker II use the TBX hub system

• Fast, Fast, Fast
• Uses the TBX hub system
• Custom cupped high rake blades provide superior bow lift and exceptional top-end speed
• Special vent holes for powerful acceleration
• Set the highest standards in top speed performance
• Maximizes the superior power and torque of Evinrude E-TEC G2 engine

Other compatible propeller options:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, Aluminum Propellers

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Return to Propellers:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke, Aluminum Propellers

Evinrude/Johnson Aluminum Props

-More Performance for the Money!  Evinrude/Johnson props are cast with a custom aluminum alloy to give them greater strength and longer life than ordinary propellers.  Many of the Evinrude/Johnson outboards are speed cupped for better top-end performance.  Special baked-on corrosion-resistant paint gives added protection against saltwater and galvanic corrosion.

• Precision casting provides greater strength and longer life
• Baked-on corrosion-resistant paint gives added protection
• Engineered to match the power curve of your outboard for superior performance.

V6 Outboard 150-300 HP & 90 - 300 HP, 25" Shaft, 2-Stroke

• 15 Spline
• TBX Propeller Hub Kit 765195  Amazon  eBay for Evinrude/Johnson props with Interchangeable Hub 
• Other TBX Propeller Kits available competitive brands.
•  
• 90 & 115 HP Evinrude® E-TEC®, 25" Shaft, 2004-thru
• 100 HP, 2004-thru
• 100 HP Commercial, 1984-thru
• 120 & 140 HP, 1985
• 130 HP, 1995-1996
• 130 HP Evinrude® E-TEC®, 2009-2010
• 135 HP, 2000-thru
• 140 HP (25"), 1989-thru
• 150 & 155 HP Commercial, 1978-thru
• 150-300 HP, Evinrude® E-TEC®, 2004-thru
• 175 HP, 1977-thru
• 185 HP, 1984-1985
• 200 HP, 1976-thru
• 225 HP, 1986-thru
• 235 HP, 1978-1985
• 2.6 liter, 1984-1985
• 250 HP, 1991-thru
• 275 HP, 1986-1988
• 300 HP, 1988-thru
• 3.6 liter, 1986-1987
• Evinrude® E-TEC® G2, 2015-thru

V6 Stern Drive 15 Spline Propellers

15 Spline
800 Series

• 3.8 - 5.7 Liter, 1978-thru

OMC Cobra®

• 4.3 - 5.7 Liter, 1986-thru

OMC Sea Drive®

• 2.0 - 4.0 Liter, 1982-thru

OMC King Cobra®

• 7.4 - 8.2 Liter, 1990-thru

Other compatible propeller options:

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Aluminum Propellers

BRP Evinrude Johnson V6 150-300 HP and 90-130 HP, 25" Shaft, 2-Stroke Stainless Steel Propellers

Return to Propellers:

18-5697 Starter Brush and Spring Set

• Sierra Brush and Spring Set
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5697
• Interchangeable with the following: Arco BK900, Chrysler F15164, 74384, Evinrude/Johnson 385952, Mercury 75384, 57390, 63292, 753841, 898265016, Mercury 75384

Power Trim Relay 586224 582472 584416 18-5705 Johnson Evinrude OMC

18-5808 STARTER SOLENOID

18-5831 Regulator/Rectifier

• Sierra Regulator/Rectifier
• Meets or exceeds the original equipment quality
• Sierra part number: 18-5831
• Interchangeable with the following: CDI 193-4641, Evinrude/Johnson 584641, 586271, 585995, Mallory 9-17205

18-5877 Stator

for 185-300 HP Loopers (1993-2001)

NIB JOHNSON EVINRUDE 185-200-225-250-300 STATOR 584643 18-5862 18-5877 173-4643

18-0492 Head Gasket

• Fits: 200 BB (1993 & Up), 225 BB (1993 & Up), 225 Ficht FFI (1999 & Up)
• 250 Carbureted only (2000)

18-4428 Powerhead Gasket Set

Replaces: 437725 Fits: 200 BB (1993 & Up), 225 BB (1993 & Up), 225 Ficht FFI (1999 & Up),

Note:  250 V6 Carbureted

V6 Loop 90 deg

18-5179 Ignition Plug In Coil

Champion 938M Spark Plug QL78YC

Also see: CHAMPION MARINE SPARK PLUG 5939  Marine Stainless Steel

• Evinrude Johnson  0.030 Gap

Mercury Outboards

• 125 HP 2004-1994  4-Cylinder 
• 115 HP 2004-1989  4-Cylinder 2-Stroke
• 100 HP 1999-1988  4-Cylinder 
• 90 HP 2006-1987  3-Cylinder 2-Stroke
• 80 HP 1989-1978
• 80 HP 2004-1995  80 Jet 
• 75 HP 2006-1987  3-Cylinder 2-Stroke 2-Stroke
• 75 HP 1986-1984  4-Cylinder
• 75 HP 2001-1990  75 Sea Pro 2-Stroke
• 70 HP 1989-1987
• 65 HP 2004-1995  65 Jet 
• 60 HP 2002-1991  3-Cylinder 
• 60 HP 2004-1995  60 Big Foot 3-Cylinder 
• 60 HP 2004-1991  60 Sea Pro 3-Cylinder 
• 55 HP 2004-1992  55 Sea Pro
• 50 HP 2004-1991  50 3-Cylinder 2-Stroke 2-Stroke
• 45 HP 1989-1986
• 45 HP 2003-199  545 Jet 3-Cylinder 
• 40 HP 2004-1995  2-Cylinder
• 40 HP 2004-1997  3-Cylinder
• 40 HP 1997-1988  4-Cylinder
• 40 HP 2004-1995  40 Sea Pro
• 30 HP 2003-1995  2-Cylinder 2-Stroke 2-Stroke
• 30 HP 2001-1998  30 Jet 3-Cylinder
• 30 HP 1997-1995  30 Jet 3-Cylinder
• 30 HP 2004-1995  30 Sea Pro 2-Cylinde
• 25 HP 2004-1980  2-Cylinder 2-Stroke 2-Stroke
• 25 HP 2002-1993  25 Sea Pro 2-Cylinder
• 20 HP 1981-1970
• 20 HP 2003-1986  2-Cylinder 2-Stroke
• 20 HP 2004-1995  20 Jet 2-Cylinder
• 10 HP 1996-1991
• 10 HP 2004-1991  10 Sea Pro
• 10 HP 1998  XR10 
• 9.9 HP 1994-1986
• 9.8 HP 1978-1970 
• 7.5 HP 1978-1970
• 4.5 HP 1985-1975
• 4 HP 1987-1986
• 4 HP 1974-1973
• 4 HP 1972
• 4 HP 1971-1970

CHAMPION MARINE SPARK PLUG 5939  Marine Stainless Steel

• 0.30 Gap

Sierra 18-1353 Center Main Bearing

• Sierra Center Main Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1353
• Interchangeable with the following: GLM 22810, Evinrude/Johnson 5007190, 387041

18-1374 Wrist Pin Bearing

• Sierra Wrist Pin Rod
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1374
• Interchangeable with the following: GLM 16220, Evinrude/Johnson 395627, Mallory 9-51103, Wiseco W5217

18-1377 Center Main Bearing

• Sierra Center Main Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1377
• Interchangeable with the following: GLM 22710, Evinrude/Johnson 352960, 320499

18-1396 Marine Lower Crankshaft Bearing

18-4068 Piston Kit  - .030 Oversize Starboard

• 3.715 inch (Starbord) (.030 oversize)
• Loopcharged Pistons For 90 degree V4/V6/V8

Sierra 18-1361 Rod Crank End Bearing

• ierra Rod Crank End Bearing
• Meets or exceeds the original equipment quality
• Sierra part number: 18-1361
• Interchangeable with the following: GLM 22820, Evinrude/Johnson 387787, Mallory 9-51100
• Fit specific, check part numbers to ensure proper fit

Sierra 18-4065 Piston Kit - Standard Bore Port

• Bore Size: 3.685 (port) (Standard Bore)
• Fit specific, check part numbers to ensure proper fit
• Loopcharged Pistons For 90 degree V4/V6/V8

434519 Johnson Evinrude OMC Trim & Tilt O-Ring & Seal Rebuild Kit

60-300 HP 1991-2006 TNT Units

18-5619 Starter

90 deg V6 V8 Loop, Standard Rotation

115-300 E-TEC