Evinrude 5.5 HP 1957 Model 5514 5515

Clymer - Evinrude Johnson Outboard Shop Manual 1.5 to 125 Hp 1956-1972  B734

• Covers 1.5 - 125 HP 2-Stroke
• 1956-1992
• Outboard Shop Manual

18-3001 Impeller

Impeller / Water Pump should be replaced every year or two.  Does not include impeller plate which does not need to be replaced every time.

18-3102  Impeller Wear Plate

18-3202 Sierra Impeller Repair Kit

This kit contains both impeller (18-3001 available separately) and wear plate (18-3102 available separately).

18-3674 Thermostat Kit

• The Sierra 18-3674 Thermostat Kit is interchangeable with the following: GLM 13280. Contains: 18-1219 Grommet Gasket, 18-0182 Thermostat Gasket, 18-3135 Stainless Steel Bolt, 18-2546 Thermostat Gasket, 18-3567 Rubber Valve, 18-3562 Valve Cup, 18-1243 Valve Spring, 18-3563 Poppet Relief Valve, 18-3565 Retainer, 18-3543 Thermostat.
• Sierra Thermostat Kit
• 18-3543 Thermostat Included
• Sierra part number: 18-3674
• Interchangeable with the following: GLM 13280

323596 Water Pump Housing

379764 Impeller

Note:  Do not use this impeller kit with plastic impeller housing.

763758 Water Pump Repair Kit with Housing

302333 Evinrude Johnson Prop Shear Pin, Propeller Drive Pin

• For Johnson Evinrude with Pin Drive Propellers
• 5.5 HP  1954-1965
• 6 HP  1965
• 7.5 HP 1950-1958
•  
• Sacrificial Part Designed to Break
• Helps prevent, or at least limit damage to your motor and prop if you hit something.
• You should have a few spares.
• Don't use the wrong, or make your shear pin from the wrong material!

Other Evinrude Johnson Prop Shear Pins, and Propeller Drive Pins

5.5 - 6 HP Aluminum Props for Johnson Evinrude  (8 x 7-1/4) Pin Drive

Fits the following Evinrude Johnson Outboards

• Pin Drive
• 5.5, 6 HP 1954-1965
• Recommended for12-14 foot boats, Light Loads.

• You probably won't find them on Amazon, but they have them on eBay.

Return to Propellers:

396514 Carburetor Float and Arm Assembly

0439071 Carburetor Kit with Float

18-7043 Sierra Carburetor Tune-Up Kit

18-7094 Carburetor Needle and Seat

18-2885 Head Gasket

18-5006 Sierra Ignition Tune-Up Kit

Kit Contains:

• 18-5199 Condenser 580321 qty 2
• 18-5156 Contact Set 580148 qty 2

Sierra International 18-5156 Contact Set

18-5181 Sierra Replacement Ignition Coil

Sierra Marine Replacement Ignition Coil.  You need one coil for each cylinder.  Old coils often become cracked or disintegrate over time because of the epoxy sealer originally used.  New coils made with different materials are much more reliable than the original.

18-5199 Condenser

Champion Spark Plug - Cj8 J8C 841

Evinrude / Johnson Gap .030

Mercury Outboards

• 15 HP 1966-1960  150    0.025
• 10 HP 1966-1960  100    0.025
• 10 HP 1966-1960  110    0.025
• 6 HP 1966-1960  60   0.025
• 3.9 HP 1966-1960  39    0.025

18-2679 Lower Unit Seal Kit

Seal Kit Contents:

• Part #     Desc.    O.E. #  Qty.
• 18-2022 Oil Seal 303345   1
• 18-2035 Oil Seal 327031   1
• 18-2891 Bearing Housing Gasket 303339 1
• 18-4248 Washer 311598 2
• 18-7100 O-Ring 301877 1
• 18-7117 O-Ring 303360 1
• 18-7120 O-Ring 307853 1
• 18-2534 Spaghetti Seal 309044 1

18-7100 O-Ring

ID: 0.245, Width: 0.155

18-7111 O-Ring

ID: 0.197, Width 0.113

18-7117 Marine O-Ring for OMC

ID: 1.060, Width: 0.135

18-7180 Marine O-Ring

ID: 0.445, Width: 0.090

18-2022 Oil Seal

Size: 0.554, OD: 1.000, Width: 0.375

18-4904 Starter Handle and Rope for Johnson/Evinrude

• Sierra Starter Handle and Rope Kit
• Rope size: #4.5
• Sierra part number: 18-4904

18-6501 Rewind Spring for Johnson/Evinrude

• Sierra Rewind Spring
• Meets or exceeds the original equipment quality
• Sierra part number: 18-6501
• Interchangeable with the following: Evinrude/Johnson 395460, 307573
• Fit specific, check part numbers to ensure proper fit

18-6513 Starter Pawl, Pack of 3